Step driver board V1.4

บอร์ดขับกระแสสำหรับยูนิโพล่าสเต็ปปิ้งมอเตอร์ขนาด 5-60 โวลต์ จ่ายกระแสสูงสุด 15 แอมป์

เราออกแบบมาเพื่อรอรับงานหนัก สามารถทำงานต่อเนื่องติดต่อกันได้หลายชั่วโมง รับประกันสินค้า 1 ปี

step-drive-board

Uni-polar step driver board

Testing for more than 4 hours.

Full & Wave step drive type setting

Two step drive type setting

Half step drive type setting

 ข้อมูลทั่วไป / Overview:

    1. ใช้สำหรับเชื่อมต่อกับ Printer IO board โดยผ่านทาง RJ-11-M, SIP 6 Pins
    2. รับสัญญาณ Dir, Step, 5V และ GND ผ่านทาง RJ-11-M, SIP 6 Pins
    3. สัญญาณ Step แบบ TTL, Active low signal input
    4. สามารถตั้งโปรแกรมรูปแบบการขับ Step motor แบบ Full or wave step (1 micro step), Two phase (1 micro step), or Half Step (1/2 micro step) ได้ด้วย DIP S/W ที่ PIN 2-3 ปรกติตั้งค่าบอร์ดโปรแกรมการขับแบบ Half Step
    5. สามารถทดสอบ step sequence testing mode ได้ด้วย DIP S/W ที่ PIN 1
    6. Automatic power save mode เมื่อไม่มีสัญญาณ Step หรือ Dir ครบ 10 วินาที ระบบจะตัดไฟฟ้าที่จ่ายไปยัง Step motor ทันที เพื่อประหยัดพลังงาน
    7. แยกชุด Step Motor Power ออกจาก Step drive board. เพื่อจ่ายไฟตรงไปยัง Step motor โดยผ่าน Terminal 5 Pins และ Modular RJ-11-F, SIP 6 Pins
    8. Power supply to board: 7-12VDC พร้อมอุปกรณ์ป้อนกันการต่อกลับขั้วไฟฟ้า ที่บอร์ดมี Regulator 5VDC สามารถจ่ายไฟ 5VDC, 500mA ผ่าน Modular RJ11-F, 6 Pins หรือป้อนไฟ 5VDC ตรงเข้าบอร์ดได้ ระวังการป้อนกลับขั้วไฟฟ้า
    9. Power supply to Motor Link board: 5-60VDC, 15Amp เพื่อป้อนให้กับ Step motor โดยตรง ระวังการป้อนกลับขั้วไฟฟ้า
    10. รับประกันสินค้า 1 ปี ตามการใช้งานปรกติ

 STEP MOTOR DRIVE BOARD SPECIFICATIONS:

    1. Support KCAM4, MACH Series, NINOS, TurboCNC etc.
    2. Uni-polar step driver design.
    3. Resolution 1, ½ micro stepping output, program selected by DIP S/W
    4. Suitable for 6, or 8 wire step motors
    5. Maximum 60VDC, 15 Amps/phase step motor output
    6. Automatic power save mode, when time pass 10 second. The step driver board will turn step motor power off.
    7. Standard 10 Ohm, 10W Resistance load current limit 1.2Amp at MOV = 12VDC.
    8. Emergency stop function for emergency stop, will stop all 6 axis port, Normally Close to GND.
    9. Printer IO board design as buffer follower port. Non invert or invert signal by change buffer IC. 74HC244 or 74HC240. Limit, Home, or Stop Signal input to computer with buffer follower.
    10. Power supply to board: 7-12VDC with reverse voltage protection and each board has 5 VDC regulator IC, which can supply 5VDC, 500mA to other boards. Or can direct input with 5VDC without reverse voltage protection.
    11. Power supply to step motor: 5 – 60VDC (MOV), separated from power supply to board. Direct drive to step motor with current limit by Resistance load. (Rload)
    12. 1 year warranty.

 

Please contact:


Penchai Marketing Co., Ltd.
Sale dept . tel: 0-2584-6137, 08-1623-4776, 08-1815-8851
Fax: 0-2584-6138
Email: This email address is being protected from spambots. You need JavaScript enabled to view it. , This email address is being protected from spambots. You need JavaScript enabled to view it. , This email address is being protected from spambots. You need JavaScript enabled to view it.

Line ID: www.penchai.com