Printer I/O board

บอร์ดสำหรับเชื่อมต่อคอมพิวเตอร์ผ่านทาง Printer port DB25

เราออกแบบมาเพื่อรอรับงานหนัก สามารถทำงานต่อเนื่องติดต่อกันได้หลายชั่วโมง รับประกันสินค้า 1 ปี

printer-io-board

Printer Input/Output link board

Testing for more than 4 hours.

Full & Wave step drive type setting

Two step drive type setting

Half step drive type setting

 ข้อมูลทั่วไป / Overview:

    1. ใช้สำหรับเชื่อมต่อกับคอมพิวเตอร์โดยผ่านทาง Printer port, DB25F connector และ Printer IO board ยังเป็น printer buffer driver แบบ inverter หรือ non-inverter signal โดยการเปลี่ยนอุปกรณ์ไอซี 74LS240 หรือ 74LS244 ตามลำดับ
    2. Printer IO board รับสัญญาณ output 12 channels จากคอมพิวเตอร์เพื่อแยกสัญญาณควบคุม Step motor ได้ 1 ถึง 6 Axis driver signal port. (Direction and Step signal)
    3. ส่งสัญญาณ input 5 channels จาก Printer IO board กลับไปยังคอมพิวเตอร์เพื่อการควบคุม เช่น Limit switch, Home position, and Stop switch. Etc.
    4. เพิ่ม Emergency Stop switch (NC, Normally close switch) ที่ Printer IO board หากเปิด switch ในกรณีเกิดอุบัติเหตุ Printer IO board จะหยุดการทำงานทุกแกนทันที
    5. Power supply to board 7-12VDC พร้อมอุปกรณ์ป้อนกันการต่อกลับขั้วไฟฟ้า และที่บอร์ดมี Regulator 5VDC สามารถจ่ายไฟ 5VDC, 500mA ผ่าน Modular RJ11-F, 6 Pins หรือป้อน 5VDC ตรงเข้าบอร์ดได้ ระวังการป้อนกลับขั้วไฟฟ้า
    6. รับประกันสินค้า 1 ปี ตามการใช้งานปรกติ

 PRINTER INPUT/OUTPUT BOARD SPECIFICATIONS:

    1. Support KCAM4, MACH Series, NINOS, TurboCNC etc.
    2. Uni-polar step driver design.
    3. Resolution 1, ½ micro stepping output, program selected by DIP S/W
    4. Suitable for 6, or 8 wire step motors
    5. Maximum 60VDC, 15 Amps/phase step motor output
    6. Automatic power save mode, when time pass 10 second. The step driver board will turn step motor power off.
    7. Standard 10 Ohm, 10W Resistance load current limit 1.2Amp at MOV = 12VDC.
    8. Emergency stop function for emergency stop, will stop all 6 axis port, Normally Close to GND.
    9. Printer IO board design as buffer follower port. Non invert or invert signal by change buffer IC. 74HC244 or 74HC240. Limit, Home, or Stop Signal input to computer with buffer follower.
    10. Power supply to board: 7-12VDC with reverse voltage protection and each board has 5 VDC regulator IC, which can supply 5VDC, 500mA to other boards. Or can direct input with 5VDC without reverse voltage protection.
    11. Power supply to step motor: 5 – 60VDC (MOV), separated from power supply to board. Direct drive to step motor with current limit by Resistance load. (Rload)
    12. 1 year warranty.

 

Please contact:


Penchai Marketing Co., Ltd.
Sale dept . tel: 0-2584-6137, 08-1623-4776, 08-1815-8851
Fax: 0-2584-6138
Email: This email address is being protected from spambots. You need JavaScript enabled to view it. , This email address is being protected from spambots. You need JavaScript enabled to view it. , This email address is being protected from spambots. You need JavaScript enabled to view it.

Line ID: www.penchai.com